4li2k73z Share your Vital activity on Facebook (More info)
close
Added a new photo album Bikes5 5/11/2014 7:13 PM
C138_016_s2f
  • C48_016_s2f

This photo album has no comments yet

Added a new photo album Bikes4 1/20/2014 5:03 PM
C138_005
  • C48_005

This photo album has no comments yet

Added a new photo album Bikes4 1/20/2014 5:03 PM
C138_005
  • C48_005

This photo album has no comments yet

Added a new photo album Bikes3 1/14/2014 2:36 PM
C138_028_2
  • C48_028_2

This photo album has no comments yet

Added a new photo album bikes2 12/15/2013 3:33 PM
C138_030
  • C48_030

This photo album has no comments yet

Added a new photo album Bikes 10/10/2013 1:20 PM
C138_057_2
  • C48_090
  • C48_097
  • C48_057_2

This photo album has no comments yet

Started new thread Axle nut stuck / stripped HELP! 9/15/2013 2:24 PM

So a few days ago I brought my rear wheel to the shop to get rebuilt (trued), and I brought it home and went to put it on and there's a problem. As I go to put my drive side axle nut on, its stripping the axle and i'm wrenching it on. The non drive side ... more »

This forum thread has 4 replies

Started new thread Fox Titan Knee/ Shin Pad Question 6/22/2013 10:17 PM

I'm going to woodward in just over two weeks and I need to get some pads. I can't spend too much so I was looking at the Fox Racing Titan Sport Knee/ Shin Combo. I was wondering if they are good and flexible for bmx since they are a combo. Does anyone ... more »

This forum thread has 8 replies

Added reply in a thread Profile Hub Problem! 6/5/2013 7:22 PM

Can you explain a little better

Added reply in a thread Profile Hub Problem! 6/5/2013 6:55 PM

Yeah but the stubborn side is just about 1mm to thin to fit the on the fork because I can't loosen it/the peg at all. I tried, hammered down on the peg and tightening but it doesn't go all the way down and slides out.

Started new thread Profile Hub Problem! 6/5/2013 5:25 PM

*I think I posted in the wrong section before So today when I went to do a smith, my front wheel started to rub. This has happened before so I went to go fix it like usual but this time i'm confused. I have a Profile Mini (female) hub and I can only ... more »

This forum thread has 7 replies

Started new thread Profile Hub Problem! 6/5/2013 4:57 PM

So today when I went to do a smith, my front wheel started to rub. This has happened before so I went to go fix it like usual but this time i'm confused. I have a Profile Mini (female) hub and I can only loosen and take out the one side bolt, the other ... more »

This forum thread has 1 reply

Added reply in a thread Crooked Grind Help 5/31/2013 8:50 PM

That might help, but I think it's more of my back peg slipping off.

Started new thread Crooked Grind Help 5/31/2013 8:24 PM

So today I was trying crooks at my local park on the one rail there. It only took me about 4 tries at first and I got it, then later when I went to film it I was having a problem. I can get into them but my pegs (mostly back) are slipping off, and i'm ... more »

This forum thread has 3 replies

Added reply in a thread Drivetrain Problem! 5/15/2013 6:31 PM

Thanks everyone, I finally figured it out. I flipped my chain around and I think it did help a little but that wasn't it. It was actually because I have 2 plastic primo dsg guards ghetto rigged on the outside of my frame because both of them did not ... more »

Added reply in a thread Drivetrain Problem! 5/15/2013 6:06 PM

I'll have to check.

Added reply in a thread Drivetrain Problem! 5/15/2013 6:04 PM

Details?

Added reply in a thread Drivetrain Problem! 5/15/2013 5:56 PM

But it's brand new how could it be stretched?

Added reply in a thread Drivetrain Problem! 5/15/2013 5:51 PM

I just realized I didn't grease it..... that's probably it.

Added reply in a thread Drivetrain Problem! 5/15/2013 5:50 PM

It's not too tight. I had it a lot tighter with my shadow chain and I didn't have this problem. 1/2 of slack maybe?