So today when landing a flat hop over a pile of dirt my cranks 'folded up' on me. I assume they slipped as I can't find any damage now that I took them apart. It was nuts. Had to ride home like I was on a scooter, or on those flow pedals. First time ... more »
Added reply in a thread Should I put on brakes 7/15/2014 11:26 AM
I love my straight cable setup, doubt Ill ever go back. It is nice to be able to go as fast as I want when I want!
Added reply in a thread If you could ride with any pro? 7/11/2014 9:01 PM
Hoder in NYC
Added reply in a thread Anyone gonna get this? 7/2/2014 5:44 PM
Added reply in a thread eerrrrrggggg I am confused.... Some Insight Please? 5/29/2014 4:09 PM
upgrade your parts, not your frame.
Added reply in a thread Cranks… 24mm & SD…. Eclat Channel 5/27/2014 7:18 PM
Tim- Its already been disassembled and boxed up for sale. Im confident it was not due to the spacers. I use 2 drive side cones (the thin ones) and my cranks cleared my frame by less than 1/2 inch on each side. I could not even jam a finger in there. ... more »
Added reply in a thread Cranks… 24mm & SD…. Eclat Channel 5/27/2014 11:53 AM
Here is a link to the photo I took right after. Has anyone else slipped a 48 spline?!?! http://instagram.com/p/oeCMaduEyS/
Added reply in a thread Cranks… 24mm & SD…. Eclat Channel 5/26/2014 5:51 AM
Running 27/9 currently, will step it up to 28 if I get a new sprocket. I was running 30/10 before this and liked it. BTW- Im still riding the 48h KHE Coaster I bought from you. Laced it to a Ribcage I found for $25 beans. Still rolling like a G. Thanks ... more »
Added bike check The Gypsy 5/25/2014 9:38 PM
Added reply in a thread Cranks… 24mm & SD…. Eclat Channel 5/25/2014 9:35 PM
LOL @ jamie. I was thinking things must work different down under!! The more I think about it I want the 165mm Indents. The Onyx don't come shorter than 170. But then I think 5mm is not going to make much difference. How is the adjustment from 175mm ... more »
Added reply in a thread Cranks… 24mm & SD…. Eclat Channel 5/25/2014 7:51 PM
OK, so I am leaning toward the Indent/Onyx and Key Guard… I really want 165mm cranks, which makes me go toward the Indents… but what is 5mm really going to matter? Any other ideas/suggestions?
Started new thread Cranks… 24mm & SD…. Eclat Channel 5/24/2014 6:18 PM
This forum thread has 20 replies
Added reply in a thread Found the scammer have fun with photos 4/25/2014 2:46 PM
try spokeo.com to see if you can find an alternate number
Added reply in a thread Found the scammer have fun with photos 4/25/2014 2:26 PM
Don't stop, you have him on tilt. He is scared if he deleted his FB and IG acts. I would blow up his mothers phone non-stop until I got some response.
Added reply in a thread 2-Tone colorways? 4/16/2014 4:56 PM
Get gum grips instead
Added reply in a thread Best Biking Gloves 4/6/2014 7:22 PM
Ive used a few pairs of Mechanix gloves and liked them. $10 at Autozone, can't go wrong. Now I have the Pryme have a nice day gloves, they also work fine. Nothing special. I don't wear gloves too often if that matters.
Added reply in a thread 48 spoke wheel set-up? 3/29/2014 10:53 PM
Added reply in a thread Watch my shitty videoo 2/2/2014 8:09 PM
Great riding, dope video! My suggestion is to cut a second or so off the front end of each clip. It will keep it moving at a more rapid pace to keep the viewers attention. Also shorten the screwing around clips, just keep the impact portion of the clip. ... more »
Added a comment about video Mike Hoder and the Lotek BTM 8/29/2013 5:36 PM
Hoder wears a 10.5? Isn't he like 6'6"?
This video has 2 comments.
Added reply in a thread Arizona? 7/12/2013 12:53 PM
I like Reed Park in Mesa. ASU in Tempe is full of spots and close too. The Wedge is not too far either, look up Scottsdale Skate park, its right next to it. If you can make it to downtown Phoenix it is heaven of ledges and rails..
Added reply in a thread Trails point of view video 7/9/2013 9:48 PM
Dope! Was that the chest mount? I just got a Hero 3 Silver, cant wait for it to cool off so I can use it.