Nick513's Forum Activity

Reply to did my first 9 set today 11/17/2009 5:51 PM

One time I cracked a crank arm on a 9 =\ No more sets for me

Reply to Garage Bowl In Progress 11/15/2009 10:33 AM

Looks pretty sick so far. This guy I know has a concrete garage bowl, it's 4 sides and goes up like 1.5 feet from the top of the garage door opening, so you have to open the garage door and climb over a big ass concrete wall to get into it.

Reply to were to get flour red sunday parts? 11/10/2009 8:40 PM

Looks like someone is looking for Sunday parts because its the cool brand

Reply to were to get flour red sunday parts? 11/10/2009 8:39 PM

Ross grips and hazard light rims are both made by Odyssey.

Reply to Sunday Completes... 11/10/2009 8:33 PM

Yup. Looks like they only come in black or one other color, depending on the bike.

New thread Sunday Completes... 11/10/2009 8:28 PM

Most of you guys have probably heard Sunday is coming out with complete bikes later this year. By the looks of it, the lowest level one is a complete pile of shit. It honestly seems like they made the name brand parts as cheap and shitty as possible, ... more »

This forum thread has 12 replies.

Reply to Self Film/Edit Backyard Sesh!! 11/7/2009 10:01 PM

Jeez so much hate...why do you people even put the effort into coming on here and bitching about everything Anyways - good riding, the ramp looks sketchy as hell but hey, whatever works

Reply to someone gimme some suggestions 11/7/2009 9:48 PM

yea the loosefer is fucking sick if you're not one of the people that follows the fads like a religion, you could look at eastern frames...the boss frame looks awesome

Reply to FUCK 11/7/2009 9:46 PM

Well you really have no one to blame except yourself

Reply to Help me with my 180s 11/7/2009 9:44 PM

It helps to carve a little bit before you spin, although I don't spin at all, fow 180s or 360s. Just hop, turn your upper body at the hips (look at your shoulder, not behind you), and you'll spin. Spinning is the type of thing that's hard to learn but ... more »

Reply to maximum height of a bmx rider 11/3/2009 10:16 AM

Chris Doyle is pretty tall too, like 6'3"

Reply to MY NECK!!!!!!!!!!! 10/31/2009 8:08 AM

of course someone named jackoff would suggest a hot shower

Reply to just made the switch. 10/30/2009 9:56 PM

Well technically as long as your gearing is in the right proportion it wouldnt make it any easier or harder to pedal. People ride small sprockets so they dont get in the way doing tricks, and because they follow the trends like sheep.

Reply to Low Riders! 10/28/2009 4:32 PM

From what I hear, lower top tubes make tailwhips/decade airs much easier.

Reply to Is The Kink Liberty A Good Bike? 10/28/2009 4:29 PM

Instead of asking strangers their opinion, take a look at the features and decide for yourself. Does it have sealed hubs/BB (it's a plus if it does)? Does it have a full chromoly frame/forks/bars? Are the bars the and frame the height/length you prefer? ... more »

Reply to who rides with knee gaskets or shin guards mayb both? 10/28/2009 4:25 PM

ridebmxnc, brave and dumb are pretty much the same thing

tongue
Anyways, I've always been meaning to get a decent pair of knee pads, but I don't know where I would get them other than online.
Reply to Smiths? 10/25/2009 6:57 PM

Well this is how I learned it...Go like you're gonna do a double peg but hop a little bit higher, then lean forward in the air. Then just learn to move your rear tire over a little bit and you'll get it...It's the type of thing that's hard to learn but ... more »

Reply to patching tube 10/24/2009 7:50 PM

No, use the duct tape first. The adhesive on duct tape it made of rubber, so when it melts it becomes airtight. Just dont overdo it and and burn another hole in your tube.

Reply to eastern vs fit 10/24/2009 7:43 PM

I snapped off an Eastern crank arm at the weld and they sent me a new pair for free without any hassle. You have to commend them on their dedication to customer service, but it's stupid to cling to a company like it's a friggin gang or something. Everyone ... more »

Reply to meeting pros 10/24/2009 12:47 PM

Aww...really?