Added reply in a thread Death by bottom bracket spacing.. 1/11/2019 3:32 AM

Well, I guess 1 good thing about a 7 year old frame is that the bb shell is quite easy to slap bearings in and out of lol, after using sand paper to sand around the inner part where the bearings set helped a lot when the frame was newer. So the trial ... more »

Added reply in a thread Death by bottom bracket spacing.. 1/8/2019 3:17 PM

I got it as close as it's gonna get with the sleeve spacer and 2 extra super thin crank spacers. Tapped my bearing in with a rubber mallet then used my home made bearing press that i made from an old 14mm wheel axel.

Added reply in a thread Death by bottom bracket spacing.. 1/8/2019 9:09 AM

Ok cool thanks

Added reply in a thread Well, ordered some new cranks 1/7/2019 4:01 PM

Chain reaction cycles, mail order

Started new thread Death by bottom bracket spacing.. 1/7/2019 3:55 PM

So with new cranks arriving soon, i am trying to take some time to set my 19mm sealed bb. I used to never run the inner sleeve spacer that goes between the bearings, but a couple of years ago i gave it another go so my cranks would spin like a champ.. ... more »

This forum thread has 24 replies

Added reply in a thread Well, ordered some new cranks 1/4/2019 7:08 AM

Yea I seen the Fit cranks but I couldn't pass up the Talons for 55 dollars brand new

Started new thread Well, ordered some new cranks 1/2/2019 1:09 PM

So even though I was iffy about the style of the cranks, I went ahead and got em anyways because I needed new. My current cranks have an issue with the threads in the sprocket boss hole. So I was looking pretty hard at the Madera bantam cranks that were ... more »

This forum thread has 5 replies

Added reply in a thread Would taller bars help me here? 12/26/2018 4:22 AM

Thx for the inputs, if it matters i will most likely never run a top load stem. Front loaders look way better

Started new thread Would taller bars help me here? 12/24/2018 7:19 AM

If i want to be able to pull up easier and make hops feel easier and smooth with my current frame.. which has a 13.75 cs slammed so my hops now feel crouched and stretched with 8.75 rise bars. For some reason I am thinking if i get like 9.25 rise bars ... more »

This forum thread has 22 replies

Added reply in a thread Eastern ti grim reaper 12/19/2018 8:09 PM

1300 bucks for a frame that has a weight limit and intended for light street riding, if any. May as well be a race frame

Added reply in a thread Video Game Tricks 11/30/2018 9:25 AM

Foot jam summersault to manual out on flat, foot jam to front hand spring while feet on pedals lol

Added reply in a thread Video Game Tricks 11/29/2018 8:39 PM

No-hand vader slide to nose manual to whiplash out, all in 1 combo without the back wheel touching down

Added reply in a thread Stuff we built 11/19/2018 8:04 PM

good stuff, you can get some huge distance on that mellow kicker. I was always good at distance jumping on kickers

Added reply in a thread KHE - forks 11/19/2018 7:37 PM

Still waiting for someone to say "are these front forks worth it"? Lol as if there were a front and rear fork on a bike. Maybe someone should design a fork with a 19mm steerer tube circumference so we can have not only front forks.. but side forks that ... more »

Started new thread shallow headtube with super steep fork 11/4/2018 9:45 AM

Just out of curiosity, I was wondering how a setup would feel with like a 74.5 HA with a steep offset fork around 15mm offset? Would if feel like a generic trails bike with a wacky front end? Or a street setup with the feel of a longer top tube...

This forum thread has 5 replies

Added reply in a thread BMX Video Contest: Challenge Ideas? 10/28/2018 9:36 AM

Highest fakie bunny hop. Would be pretty hard to measure because setting a bar up to hop over while going backwards would be quite difficult and dangerous lol... but that's my thought, or best trick while fakie hopping.

Added reply in a thread Shot of the day 10/18/2018 5:08 PM

Added reply in a thread Anyone ride Merritt cranks? 10/13/2018 9:31 AM

heavy duty heat treated street cranks, should have no problems with them. Hit up Charlie Crumlish and ask him how they hold up lol. Did you see the how-to install the battle cranks on youtube? I watched it a few months ago just to get a closer look at ... more »

Added reply in a thread Any 10t coasters on the market? 9/23/2018 11:23 AM

I had 28-10 gearing on a bike a while ago and liked it alot, and i might invest in a coaster soon. As far as cassettes go, only few still make 10t like madera, profile, maybe primo

Started new thread Any 10t coasters on the market? 9/23/2018 6:49 AM

Does any company make 10tooth freecoasters?

This forum thread has 12 replies