Added reply in a thread Best chain in your opinion 7/15/2013 1:12 PM

tbh just get yourself a 10$ kmc chain the half links snap just as easy and you can buy like 3-5 kmc chains compaired to most other chains

Added reply in a thread question for trail/park riders 7/15/2013 1:07 PM

i like the odyssey slim by four pads but i also use chrome rims so really any pads work for me but if you have painted rims the clear ones still rip the paint off so i wouldnt bother getting clear ones

Added reply in a thread Over clicking turndowns 5/21/2013 8:19 AM

if you kick out your backend more it alows you to get over the bars more and overclick it

Added reply in a thread Airless / Cut-out tires 5/19/2013 7:03 AM

it would prob be good for road bikes but for bmx i dont think its going to catch on. and personaly i like some good old fashion rubber.

Added reply in a thread Fuck. Last question on 180s 5/19/2013 7:00 AM

what i did when i started learning 180s was learn them on a kicker/funbox or even a quarter pipe because you dont have to worry about doing a fakie, and it also helps with getting air. once you try them on some ramps first then go to flat and try them ... more »

Added reply in a thread how to fakie longer 5/19/2013 6:50 AM

well when i first started fakies i learned them going down a slope and on quarter pipes, but when i started doing 180s i used a 2-3 crank speed to start off with then went up from there. The only time i land with my tire curved is if i need to fakie ... more »

Added reply in a thread Help with taking profile cone washer off for hubguard! 5/18/2013 6:55 PM

thanks but i actually just took the whole axel off and got it off that way :/ ill keep that in mind tho next time i do it :D

Started new thread Help with taking profile cone washer off for hubguard! 5/18/2013 3:08 PM

Ok so my hubguards arrive today! YAY! but upon installation i find that this cone washer isnt coming off, any tips? its on there tight and i dont want to hit anything cause this hub is new. if anyone could help it would be greatly appreciated. THANKS! ... more »

This forum thread has 3 replies

Added reply in a thread Handlebar Rise ? and Opinion 5/16/2013 1:56 PM

i know what you mean. since you are 6ft i would prob go with 8.25 rise or even 8.5 rise. what i did when i bought different rise bars was i went to my local bmx shop and rode some complete bikes that had the size i was looking at buying to kinda get ... more »

Added reply in a thread Handlebar Rise ? and Opinion 5/16/2013 10:53 AM

when i got my new bars they were 8.5" rise and like 28" wide my old bars were 7.75" rise and like 25" wide. for me it was a big change but once i started riding them for a while i really liked them tbh i wouldent go anything bigger than a 8.5" rise. ... more »

Added reply in a thread HELP... Primo n4fl bearing replacement 5/16/2013 10:36 AM

ive never had one of these hubs but if you had a picture or 2 of the inside of the hub and bearings i could try my best to help

Added reply in a thread how to fakie longer 5/16/2013 10:32 AM

did you even read what i wrote?

Added reply in a thread how to fakie longer 5/15/2013 5:50 PM

i forgot to mention that you want to backpedal only a lil bit faster than your cranks this might help cause i see a lot of people that try learning fakies and they just backpedal way too fast

Added reply in a thread how to fakie longer 5/15/2013 5:46 PM

Just keep practicing fakies on a slope or ramp and try getting to were you will be able to fakie at a higher speed. some tips when i fakie is to stare at my stem and keep my weight more toward the backend. when you do your 180s try going a lil faster ... more »

Added reply in a thread Plastic pegs? 5/14/2013 8:52 PM

allright guys thanks ill prob get an extra set of sleeves too just in case

Added reply in a thread Plastic pegs? 5/14/2013 7:52 PM

How often does the plastic sleeve normally wear out?

Started new thread Plastic pegs? 5/14/2013 7:37 PM

Ive never actually used these before i was just wondering how they grind and hold up cause i thought about buying a set to try out

This forum thread has 10 replies

Added reply in a thread 360 HELP!!!!!!!! 5/14/2013 7:14 PM

What i did even though you have tire taps down try carving about almost at 90 and then do your rotation and when you get it all the way around and feel comfortable doing around 270s then just start carving less and less and always make sure you turn ... more »

Added reply in a thread KINK ORION RIM 5/14/2013 6:58 PM

i used to run it in the back untill i got my new rims (g-sport rollcages) they are kinda the same style of rib and wall but id say if your lookin at getting a good rim you would be good with either the orion, g-sport rollcage, or the odyssey 7KA rim ... more »

Added reply in a thread What hubguards with profile hubs? 5/14/2013 1:19 PM

Wow! thanks i could of swore when i checked it was only 3/8 thanks man!