29 tooth sprocket

Related:
Create New Tag

9/11/2013 7:55 PM

I recently bought some fit 24 mm cranks and figure I would pick up a new sprocket while I was at it. I can't seem to find one with a bigger bore. Can't seem to find hardly any 29 tooth sprockets. I have a 3O tooth now but it is super close to hitting the frame.. Any one know of a 29 that will work for me. Or where to find one. It would be super rad if it were red..

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/11/2013 7:58 PM

just get a 28 tooth it wont make much of a difference and you can get a half link to adjust your cs length, and ik there are some that will fit the indent 24s and that are red

|

MIDWEST MOTHER FUCKER

Bike Check
Bought from Tomdon, and ScramHype

9/11/2013 7:59 PM

i dont think anybody makes 29. its one of those odd numbers.

|

Old bike VVV

California Living

I now have a more or less stock sunday scout with a complete Demo rear wheel. Sue me

9/11/2013 8:26 PM

29 is already going as low as I want to go. 30 is perfect but need more clearance. I saw a few ppl making 29s I just dont know where to buy them or if the bore is enough for the 24mm spindle. BSD and Profile are the ones I have seen. I dong think the Profile will work and can't find the BSD. No red either.. Guess worst case I get a 28 t but not really wanting to do that.

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/11/2013 8:30 PM

Just keep your 30 and throw a skinny spacer on the drive side.

|

9/11/2013 8:30 PM

ugot2dewitt wrote:

29 is already going as low as I want to go. 30 is perfect but need more clearance. I saw a few ppl making 29s I just dont know where to buy them or if the bore is enough for the 24mm spindle. BSD and Profile are the ones I have seen. I dong think the Profile will work and can't find the BSD. No red either.. Guess worst case I get a 28 t but not really wanting to do that.

suck it up and get a 28

|

Check out my youtube channel!! http://www.youtube.com/user/mikel8149

9/11/2013 8:43 PM

Running 11 tooth in rear

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/11/2013 8:44 PM

Put a spacer inbetween the bb cone washer and the sprocket. Will fuck up your chain alignment a bit but its all you can do

|




Refs : SnM An1mal, GThompson121, Chuck8273, blizzbikes, bmxsteve99, kevin.brock.338, zinum, Brian_Griffin, billyhandyjunior, riverM, tomdon
Instagram : @timhankinsbmx


9/11/2013 8:44 PM

Or bore out your own sprocket

|




Refs : SnM An1mal, GThompson121, Chuck8273, blizzbikes, bmxsteve99, kevin.brock.338, zinum, Brian_Griffin, billyhandyjunior, riverM, tomdon
Instagram : @timhankinsbmx


9/11/2013 8:44 PM

BNC wrote:

Just keep your 30 and throw a skinny spacer on the drive side.

Yeah think I will try that thanks

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/11/2013 10:25 PM

All odyssey sprockets will run on the 24mm spindle. I'm not sure but I think they have 29t cause they do some other un usual sizes like 27.

Could also talk to tree. Pretty sure they can custom bore you one of there sprockets

|

I'm a punk bmxer, I can't do it well so I do it loud.

9/11/2013 11:37 PM

15/16 bore will fit the spindle perfectly. i ran a tuffman which is 15/16 when i had my 24mm indents. i know that doesnt help the tooth size issue, but now you know the bore at least.

|

bikes destroy vlogs.

ref: slade_vincent, shutta, ecuadevil, theprophet, blackmammoth, sfb, element4all, bmx-junkie, kurtnut, nickg, jessebmx, dontDELETE, krbmx17, ninjacat, freddydapice, waanng, ivan, scramhype, motogrizz, tomdon, dream, hatebreeder, noendinsight666, asilva, wolfen, superstarDK, skubasteve, aebasher, many more.

9/11/2013 11:39 PM

Fit make a 29t Sprocket, or at least they did last time I checked.

|

9/12/2013 12:19 AM

Gump wrote:

All odyssey sprockets will run on the 24mm spindle. I'm not sure but I think they have 29t cause they do some other un usual sizes like 27.

Could also talk to tree. Pretty sure they can custom bore you one of there sprockets

I contacted Tree.. I didn't realize but I grew up in the same town that they are located in.. Hope they can help..

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/12/2013 9:17 AM

|

9/12/2013 12:29 PM

Called em. Not a big enough bore.. fuck! They said Fit makes one they think.

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/12/2013 12:37 PM

The guys at fit said they made some but no longer have em. Guess I'm gonna suck it up and get a 28.

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/12/2013 12:46 PM

These will fit

|

9/12/2013 12:51 PM

BRANDON_90 wrote: Check this one out.

BNC wrote:

These will fit

Yeh these have a big enough bore. and are red. and 29 t

|

9/12/2013 1:25 PM

Dont they have a 22mm bore? Seems to be what I found on them anyway

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/12/2013 1:29 PM

No i looked and double checked.

|

9/12/2013 1:30 PM

|

9/12/2013 1:56 PM

Good deal thanks guys.. I ordered one.. I'm a cheap bastard so I got the gold one at half price.

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim

9/12/2013 2:13 PM

Nice!

|

9/13/2013 1:17 PM

So they contacted me this morning and said that they are out of gold and would I like a different color. They are sending me a red one! smile

|

Over 500+ transactions on eBay at 100%. - jddewitt
Refs: nshs2010, handlebar-to-face, HardBMX_Tim